on some newer models) to protect the heating element. unplug the station while this cooling cycle is active. 3. Operating Parameters Range / Specification Hot Air Temp (recommended for general use) Soldering Iron Temp Airflow Stepless adjustment, max 120 L/min Power Consumption
| Symptom | Old Manual Suggestion | | | :--- | :--- | :--- | | Air comes out, but no heat | Replace heating element | Check the reed switch inside the handpiece. New models require the handle to be fully seated in the stand to deactivate sleep mode. | | Soldering iron reads "H-E" | Replace handle | This means "Heating Element Error." Unplug the iron. The screw collar often loosens. Tighten the brass ring inside the handle. | | Display flickers / fan surges | Return unit | Update: This is usually a dirty airflow potentiometer. Rotate the airflow knob from 1 to 8 rapidly 20 times (with unit off) to clean the wiper. | | Temperature swings wildly | Calibrate | The stock PID algorithm is slow. Set your airflow to level 4 or lower. High airflow cools the heater faster than the controller can react. |
(typically 2–3 red screws) located on the bottom of the unit. Failure to do so will cause severe vibration, excessive noise, and permanent damage to the internal diaphragm pump. Technical Specifications Hot Air Rework Station Soldering Iron Power Consumption Temperature Range 100°C – 500°C 200°C – 480°C Airflow Capacity 0.3 – 24 L/min (Diaphragm Pump) Heating Element Metal Heating Core Ceramic Core (900M Tips) Safety Standard Operating Guidelines Rework Station SS-952C-F Series - Farnell
Insert the 5-pin DIN plug into the front receptacle and screw down the locking ring. Power On: Flip the soldering iron power switch.
Disclaimer: This guide is based on standard operational practices for the Gordak 952. Always follow the specific instructions included with your machine. gordak 952 user manual updated
Before diving into the user manual, let's take a look at some of the key features that make the Gordak 952 a standout device:
The updated manual for your device will typically include the most recent iteration of the diagrams, safety warnings, and operating procedures tailored to the specific hardware version you own. If you cannot find the physical copy, official documents for the entire series are often available from Gordak’s official distributors or electronics forum repositories like , which provides service manuals and schematics.
The Gordak 952 is covered by a limited warranty. For more information, please refer to the warranty document provided with the device. Additional support resources are available:
Complete User Manual: Gordak 952 Rework Station (Updated Edition) Safety Precautions and Setup on some newer models) to protect the heating element
Use the Air Volume dial to set your desired airflow level. Turn the temperature knob clockwise to increase heat.
Gordak 952 User Manual & Guide (Updated 2026) The is a widely used 2-in-1 SMD rework station featuring an integrated hot air gun and a 60W soldering iron. Designed for desoldering and soldering components like QFP, PLCC, SOP, and BGA, it is a staple for professional electronics repair. Technical Specifications
When finished, turn off the hot air heater switch but leave the main power on. The unit will continue blowing cold air to reduce the element temperature safely below 100∘C100 raised to the composed with power C before turning off the pump automatically. Using the Soldering Iron
The Gordak 952 is a high-performance device designed to provide precise control and measurement of various electrical parameters. Its advanced features and user-friendly interface make it an ideal tool for professionals and hobbyists alike. This manual covers the following topics: Operating Parameters Range / Specification Hot Air Temp
Check the 5-pin connection. Inspect the main power fuse located at the back of the station near the power cord. Oxidized soldering tip or uncalibrated station.
The Gordak 952 is engineered to facilitate independent usage without interference between its two primary functions: a hot air rework gun and a standard soldering iron. The "Updated Manual" referenced here consolidates the latest technical insights, safety protocols, and practical use cases based on recent user feedback and engineering data.
While still rare, some updated versions of the manual include exploded diagrams with updated part numbers. If you need to replace a handle, a heating coil, or a specific IC on the motherboard, the new manual is a better resource for ordering the correct replacement parts.